Prostripe Plus Waterborne Traffic Paint

Prostripe Plus Waterborne Traffic Paint
Prostripe Plus Waterborne Traffic Paint
Brand: Medallion Series
Product Code: Prostripe Plus

Available Options

* Color:

   - OR -   

Fast drying 100% acrylic waterborne paint specifically designed to be applied by walk-behind striping machines for parking lot or roadway striping. Formulated with high solids for more coverage, durability and brighter colors. Will not discolor when used over freshly sealed asphalt and is formulated to reduce new asphalt cracking. Lead free, low VOC's and non-hazardous. Exceeds Fed Spec TTP-1952-D.

Product Features

  • Formulated with high solids and pigment yielding more coverage, durability and brighter colors
  • Meets TTP-1952-E Type I and II Federal Spec and is lead free with low V.O.C's for safer application and disposal
  • Will not discolor when used over freshly sealed asphalt
  • Formulated for reduced new pavement cracking, bleed through and fading

Want to know when the weather will be best for striping? Check the DAF Scale for your area today! 


Material Preparation
Mix thoroughly before using. Prostripe Plus™ will generally need no alteration prior to spray application. See application section.

Surface Preparation
Surfaces should be dry, clean and free of oil, grease, dust and other foreign matter.

May be sprayed through machines specifically designed to spray traffic paint. If rolling or brushing is necessary, Prostripe Plus™ may need water added to slow dry time. Recommended film thickness is 13-15 mils wet.

Do not apply on new asphalt when surface temperatures exceed 115°F. This could cause severe cracking or peeling of the asphalt. If application is absolutely necessary under these conditions, thoroughly mix water (maximum 12oz. per five gallon pail) to Prostripe Plus™ and apply a test stripe in an inconspicuous area. Let set for minimum of ½ hour and inspect cracking along stripe’s edge. If cracking appears await cooler temperatures before application.

Surface temperatures may vary from section to section. Applying less mils can also further reduce cracking.

Glass beads should be applied by any suitable method which can be regulated to dispense six pounds of glass beads per gallon of paint. When applying glass beads to a rolled or brushed line or legend, they must be applied at the same time the marking is applied.

Do not apply acrylic water reducible traffic paints when temperature is below 50°F or humidity is above 85%. Do not apply if rain is expected within 4 hours.

Equipment clean up:
100% Durable Acrylic Cleanup of utensils and machinery can be best accomplished by using warm soapy water. Do not use organic solvents.

Pintura para marcado de carretera, transmitida por agua, de secado rápido, es 100% acrílica, especialmente formulada para aplicarse por maquinas pintadoras manuales en las cuales el operario camina atrás de ellas.  Utilizada para pintar el marcaje en estacionamientos y carreteras.  Formulada con una alta cantidad de sólidos para más cobertura, durabilidad y colores más brillantes.  No se descolora cuando se usa sobre sellador de asfalto recién aplicado, también ayuda a reducir las grietas en el asfalto.  No contiene plomo, tiene bajo numero de COVs y no representa riesgos para la salud.  Excede la norma Fed Spec TTP-1952-D.  Se vende por cubeta de 5 galones.

Caracteristicas del Producto

  • Formulada con una alta cantidad de solidos, da mas coverture, durabilidad y colores mas brillantes.
  • Cumple con la norma Federal TTP-1952-E Tipo 1 y 2, no contiene plomo y con bajos VOC’s para una aplicacion y desecho mas segura.
  • No se decolora cuando se aplica sobre sellador de asfalto recien aplicado
  • Formulada para reducir agrietamiento en asfalto Nuevo, escurrimiento y decoloracion.
Additional Info
Coverage Rate Approximately 350 lf 4" line per gallon
Special Order Qualified DOT formulations available

Write a review

Your Name:

Your Review: Note: HTML is not translated!

Unsatisfactory            Excellent

Enter the code in the box below: